Oscilloscope Probes

An oscilloscope is considered to be the most used instrument for electrical engineers who need to measure electrical characteristics of electronic devices but you also need at least one probe.
Things to consider when choosing probes
• Ensure the probe's input connector matches the connector on your scope
• Choose a probe whose input resistance and capacitance match the input resistance and capacitance of your scope - matching is critical for guaranteeing proper signal transfer and signal accuracy
The best approach, for matching a probe with a scope, is to first choose a probe whose capacitance is within the range of your scope and then fine-tune the probe's capacitance by adjusting its compensation network using the probe's trimmer capacitor.
The 1X probes are suitable for many low frequency applications. They typically offer the same input impedance of the oscilloscope which is normally 1 M Ohm. The most common type of probe with a built in attenuator gives an attenuation of ten, and it is known as a 10X oscilloscope probe
Types of probes
Passive probes are the most commonly used probes for taking measurements. They are easy to use, relatively inexpensive, and fairly rugged. Available in the following configurations:
• 1´: no attenuation
• 10´: factor-of-10 attenuation
• 100´: factor-of-100 attenuation
• 1000´: factor-of-1000 attenuation
Attenuation probes serve to multiply the voltage measurement range of the oscilloscope by using an internal resistor that, when used in conjunction with the input resistance of the scope, creates a voltage divider. Useful for the following reasons:
• It allows for the measurement of a signal that might exceed the limits of the oscilloscope.
• The attenuation circuitry results in higher resistance and lower capacitance, which is important for high-frequency measurements.
Active probes contain active components, such as FETs or amplifiers. Commonly used for taking high-speed measurements (>500 MHz) or on high-impedance circuits. One limitation is their limited voltage range.
Differential probes are popular for measuring high-frequency signals or signals of very low amplitude.
A current probe measures the electrical current flowing through a conductor.
Tips
• Always use an appropriate probe tip and/or probe tip adapter whenever possible
• Keep ground leads short

...
Read more Read less

Filters

Viewing 1 - 18 of 18 products
Results per page
Description Price Probe Type Attenuation Bandwidth Maximum Common Mode Input Voltage Connector Type Model Number p Number of Probes Safety Category Level Safety Category Voltage Calibrated Series Safety Category Rise Time Minimum Bandwidth
RS Stock No. 201-1879
Mfr. Part No.RT-ZS20
kr 24 045,00
Each
Units
Active 10:1 1.5GHz - BNC RT-ZS - - - - - - - -
RS Stock No. 201-1875
Mfr. Part No.RT-ZHD16
kr 22 470,00
Each
Units
High Voltage 50:1, 500:1 200MHz - BNC RT-ZHD - - - - - - - -
RS Stock No. 201-1885
Mfr. Part No.HZ-17
kr 8 820,00
Each
Units
Near Field Probe Set 10:1 3GHz - - HZ-17 - - - - - - - -
RS Stock No. 201-1873
Mfr. Part No.RT-ZHD07
kr 21 945,00
Each
Units
High Voltage 25:1, 250:1 200MHz - BNC RT-ZHD - - - - - - - -
RS Stock No. 201-1881
Mfr. Part No.RT-ZS60
kr 62 790,00
Each
Units
Active 10:1 6GHz - BNC RT-ZS - - - - - - - -
RS Stock No. 144-8208
Mfr. Part No.RT-ZP03
kr 840,00
Each
Units
Passive 1:1, 1:10 >300MHz - BNC RT-ZP03 1 - - - RT-Z - 1.15 ns, 35ns -
RS Stock No. 201-1886
Mfr. Part No.RT-ZI10C
kr 3 255,00
Each
Units
Passive 10:1 500MHz - BNC RT-ZI10C - - - - - - - -
RS Stock No. 201-1874
Mfr. Part No.RT-ZHD15
kr 19 635,00
Each
Units
High Voltage 50:1, 500:1 100MHz - BNC RT-ZHD - - - - - - - -
RS Stock No. 201-1880
Mfr. Part No.RT-ZS30
kr 46 935,00
Each
Units
Active 10:1 3GHz - BNC RT-ZS - - - - - - - -
RS Stock No. 201-1877
Mfr. Part No.RT-ZS10
kr 15 960,00
Each
Units
Active 10:1 1GHz - BNC RT-ZS - - - - - - - -
RS Stock No. 201-1882
Mfr. Part No.RT-ZZ80
kr 21 000,00
Each
Units
Passive 10:1 8GHz - BNC, SMA adapter RT-ZZ80 - - - - - - - -
RS Stock No. 201-1869
Mfr. Part No.RT-ZD20
kr 50 715,00
Each
Units
Differential 10:1 1.5GHz - BNC RT-ZD - - - - - - - -
RS Stock No. 201-1876
Mfr. Part No.RT-ZHD60
kr 38 010,00
Each
Units
High Voltage 100:1, 1000:1 100MHz - BNC RT-ZHD - - - - - - - -
RS Stock No. 201-1868
Mfr. Part No.RT-ZD10
kr 40 215,00
Each
Units
- 1:10, 1:100 1GHz - BNC RT-ZD - - - - - - - -
RS Stock No. 201-1870
Mfr. Part No.RT-ZD30
kr 62 790,00
Each
Units
Differential 10:1 3GHz - BNC RT-ZD - - - - - - - -
RS Stock No. 201-1878
Mfr. Part No.RT-ZS10E
kr 12 705,00
Each
Units
Active 10:1 1GHz - BNC RT-ZS - - - - - - - -
RS Stock No. 201-1871
Mfr. Part No.RT-ZD40
kr 71 715,00
Each
Units
Differential 10:1 4.5GHz - BNC RT-ZD - - - - - - - -
RS Stock No. 144-8209
Mfr. Part No.RT-ZP05
kr 2 310,00
Each
Units
Passive 1:10 500MHz - BNC RT-ZP05 1 - - - RT-Z - 0.7ns -