Microchip USB3343-CP, USB Transceiver, USB 2.0-OTG, 1.8 → 3.3 V, 24-Pin QFN

  • RS Stock No. 893-8253
  • Mfr. Part No. USB3343-CP
  • Brand Microchip
Technical Reference
Legislation and Compliance
RoHS Certificate of Compliance
Product Details

USB334x Series USB 2.0 Transceivers

The USB334x family of devices from Microchip are Hi-Speed USB2.0 ULPI Transceivers that support USB-IF Battery Charging 1.2 (BC 1.2) specification.

Features

USB-IF Battery Charging 1.2 Specification Compliant
Link Power Management (LPM) Specification Compliant
Integrated ESD protection circuits – Up to ±25kV IEC Air Discharge without external devices
Over-Voltage Protection circuit (OVP) - protects the VBUS pin from continuous DC voltages up to 30V
Integrated USB Switch - USB3341, USB3346, and USB3347 models only
Microchip’s RapidCharge Anywhere™:
- 3-times the charging current through a USB port over traditional solutions
- USB-IF Battery Charging 1.2 compliance to any portable device
- Charging current up to 1.5Amps via compatible USB host or dedicated charger
- Dedicated Charging Port (DCP), Charging (CDP) & Standard (SDP) Downstream Port support
flexPWR® Technology - Extremely low current design ideal for battery powered applications
Single Power Supply Operation - Integrated 1.8V and 3.3V regulators
PHYBoost – Programmable USB transceiver drive strength for recovering signal integrity
VariSense™ - Programmable USB receiver sensitivity
“Wrapper-less” design for optimal timing performance and design ease
External Reference Clock operation available
Smart detection circuits allow identification of USB charger, headset, or data cable insertion
Includes full support for the optional On-The-Go (OTG) protocol detailed in the On-The-Go Supplement Revision 2.0 specification
Supports the OTG Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)
UART mode for non-USB serial data transfers
Internal 5V cable short-circuit protection of ID, DP and DM lines to VBUS or ground

USB (Universal Serial Bus) - Microchip

Specifications
Attribute Value
Number of Transceivers 1
Protocols Supported USB 2.0-OTG
Power Supply Type Single
ESD Protection Yes
Typical Single Supply Voltage 1.8 → 3.3 V
Mounting Type Surface Mount
Package Type QFN
Pin Count 24
Dimensions 3.95 x 3.95 x 0.9mm
Height 0.9mm
Length 3.95mm
Maximum Operating Temperature +85 °C
Width 3.95mm
Minimum Operating Temperature -40 °C
Discontinued product
Related Products
The MCP2561/2 is Microchip Technology Inc. second generation ...
Description:
The MCP2561/2 is Microchip Technology Inc. second generation high-speed CAN transceiver. It serves as an interface between a CAN protocol controller and the physical two-wire CAN bus. The device family members are: • MCP2561 with SPLIT pin • MCP2562 with ...
Micrel 10/100Base-TX MAC/PHY Controllers offer the perfect solution ...
Description:
Micrel 10/100Base-TX MAC/PHY Controllers offer the perfect solution for adding high throughput, cost effective Ethernet connectivity.
The KSZ8864RMN is a highly-integrated, Layer 2 managed ...
Description:
The KSZ8864RMN is a highly-integrated, Layer 2 managed 4-port switch with optimized design, plentiful features and smallest package size. It is designed for cost-sensitive 10/100Mbps 4-port switch systems with on-chip termination, lowest-power consumption, and small package to save system cost. ...
The KSZ9031 reduces board cost and simplifies board ...
Description:
The KSZ9031 reduces board cost and simplifies board layout by using on-chip termination resistors for the four differential pairs and by integrating an LDO controller to drive a low-cost MOSFET to supply the 1.2V core. Single-chip 10/100/1000Mbps Ethernet transceiverKSZ9031Mxx feature ...