Oscilloscope Probes

An oscilloscope is considered to be the most used instrument for electrical engineers who need to measure electrical characteristics of electronic devices but you also need at least one probe.Things to consider when choosing probes Ensure the probe's input connector matches the connector on your scope Choose a probe whose input resistance and capacitance match the input resistance and capacitance of your scope - matching is critical for guaranteeing proper signal transfer and signal accuracyThe best approach, for matching a probe with a scope, is to first choose a probe whose capacitance is within the range of your scope and then fine-tune the probe's capacitance by adjusting its compensation network using the probe's trimmer capacitor. The 1X probes are suitable for many low frequency applications. They typically offer the same input impedance of the oscilloscope which is normally 1 M Ohm. The most common type of probe with a built in attenuator gives an attenuation of ten, and it is known as a 10X oscilloscope probeTypes of probesPassive probes are the most commonly used probes for taking measurements. They are easy to use, relatively inexpensive, and fairly rugged. Available in the following configurations: 1´: no attenuation 10´: factor-of-10 attenuation 100´: factor-of-100 attenuation 1000´: factor-of-1000 attenuationAttenuation probes serve to multiply the voltage measurement range of the oscilloscope by using an internal resistor that, when used in conjunction with the input resistance of the scope, creates a voltage divider. Useful for the following reasons: It allows for the measurement of a signal that might exceed the limits of the oscilloscope. The attenuation circuitry results in higher resistance and lower capacitance, which is important for high-frequency measurements.Active probes contain active components, such as FETs or amplifiers. Commonly used for taking high-speed measurements (>500 MHz) or on high-impedance circuits. One limitation is their limited voltage range. Differential probes are popular for measuring high-frequency signals or signals of very low amplitude.A current probe measures the electrical current flowing through a conductor. Tips Always use an appropriate probe tip and/or probe tip adapter whenever possible Keep ground leads short

...
Read more Read less

Filters

Viewing 21 - 40 of 192 products
Results per page
Description Price Probe Type Attenuation Bandwidth Maximum Common Mode Input Voltage Connector Type Model Number p Number of Probes Safety Category Level Safety Category Voltage Series Safety Category Rise Time
RS Stock No. 728-6759
Mfr. Part No.TPP1000
BrandTektronix
kr 10 389,60
Each
Units
Passive 1:10 1GHz 300V - TPP1000 - CAT II 300V 4000, 5000 CAT II 300 V -
RS Stock No. 797-3390
Mfr. Part No.TPP0500B
BrandTektronix
kr 6 204,90
Each
Units
Passive 1:10 500MHz 300V Hook Clip TPP0500B 1 CAT II 300V TPP0 CAT II 300 V -
RS Stock No. 733-6148
Mfr. Part No.N2796A
kr 21 854,24
Each
Units
Active 1:10 2GHz - - N2796A - - - N - 175ps
RS Stock No. 512-6438
Mfr. Part No.TT-SI 9101
BrandTestec
kr 7 507,00
Each
Units
Active, Differential 1:10, 1:100 100MHz 1kV BNC TT-SI 9101 - CAT III 1000V ac SI CAT III 1000 V ac 3.5ns
RS Stock No. 224-1219
Mfr. Part No.15101
BrandTestec
kr 3 208,25
Each
Units
Active, Differential 1:10, 1:100 25MHz 700V BNC TT-SI 9001 - CAT III 1000 V ac, 1400 V ac/dc SI CAT III 1000 V ac, CAT III 1400 V 14ns
RS Stock No. 851-3087
Mfr. Part No.HVP120
kr 4 429,80
Each
Units
Passive 1:100 400MHz - BNC HVP120 - CAT I, CAT II 1000 Vrms, 6000 V HVP CAT I 6000 V, CAT II 1000 Vrms 900ps
RS Stock No. 898-6785
Mfr. Part No.TA223
kr 18 152,38
Each
Units
Active 1:10 2.5GHz 20V BNC Adapter, SMA - 2 - 20V - - -
RS Stock No. 715-8733
Mfr. Part No.TPP0101
BrandTektronix
kr 529,10
Each
Units
Passive, Voltage 1:10 100MHz 300V BNC TPP0101 - CAT I, CAT II 300 V, 300 V ac, 400 V ac TPP CAT I 400 V ac, CAT II 300 V, CAT II 300 V ac 3.5ns
RS Stock No. 796-6718
Mfr. Part No.P6247
BrandTektronix
kr 53 391,00
Each
Units
Differential 1:1, 1:10 1GHz 25V BNC P6247 1 - - - - 350ps
RS Stock No. 734-5035
Mfr. Part No.P5210A
BrandTektronix
kr 32 227,00
Each
Units
Differential, Gripper, High Voltage 1:100, 1:1000 50MHz 5.6kV - P5210A - CAT I, CAT III 1000 V, 2300 V P52XXA CAT I 2300 V, CAT III 1000 V -
RS Stock No. 733-6139
Mfr. Part No.N2795A
kr 10 777,57
Each
Units
Active 1:10 1GHz - - N2795A - - - N - 350ps
RS Stock No. 752-7357
Mfr. Part No.THDP0200
BrandTektronix
kr 20 298,20
Each
Units
Differential, High Voltage 1:50, 1:500 200MHz 1.5kV BNC THDP0200 - CAT II, CAT III 600 V, 1000 V THD CAT II 1000 V, CAT III 600 V 1.8ps
RS Stock No. 715-8743
Mfr. Part No.TPP0201-PK10
BrandTektronix
kr 570,466
Each (In a Pack of 10)
Units
Passive 1:10 200MHz 300V BNC TPP0201 - CAT I, CAT II 300 V, 300 V ac, 400 V ac TPP CAT I 400 V ac, CAT II 300 V, CAT II 300 V ac 2.3ns
RS Stock No. 734-5026
Mfr. Part No.P5205A
BrandTektronix
kr 16 065,40
Each
Units
Differential, High Voltage 1:50, 1:500 100MHz 1kV - P5205A - CAT II 1000V P52XXA CAT II 1000 V -
RS Stock No. 752-7353
Mfr. Part No.THDP0100
BrandTektronix
kr 34 343,40
Each
Units
Differential, High Voltage 1:100, 1:1000 100MHz 6kV BNC THDP0100 - CAT I, CAT III 1000 V, 2300 V THD CAT I 2300 V, CAT III 1000 V 3.5ps
RS Stock No. 512-5025
Mfr. Part No.MTX1032-C
BrandMetrix
kr 5 733,00
Each
Units
Differential 1:10, 1:100 50MHz - BNC MTX 1032-C 7 CAT II 600V - CAT II 600 V 7ns
RS Stock No. 734-5013
Mfr. Part No.P5100A
BrandTektronix
kr 5 291,00
Each
Units
Passive 1:100 500MHz 1kV - P5100A - CAT II 1000V ac 5000 CAT II 1000 V ac 700ps
RS Stock No. 512-5003
Mfr. Part No.MX9030-Z
BrandMetrix
kr 3 400,00
Each
Units
Differential, Gripper 1:1, 1:20, 1:200 30MHz - - MX 9030-Z 5 CAT IV 600V - CAT IV 600 V 11.7ns
RS Stock No. 518-0987
Mfr. Part No.99.00173
BrandStaubli
kr 699,00
Pr. Set
Set(s)
Passive 1:10 250MHz - BNC 99.00173 - CAT II, CAT III 600 V, 1000 V - CAT II 1000 V, CAT III 600 V 1.2ns
RS Stock No. 825-1209
Mfr. Part No.68.9556-28
BrandStaubli
kr 977,16
Pr. Set
Set(s)
Passive 1:10 500MHz - BNC 68.9556-28 1 CAT III, CAT IV 600 V, 1000 V SET Isoprobe CAT III 1000 V, CAT IV 600 V -
Related Products
This unique probe is designed with two eight-channel ...
Description:
This unique probe is designed with two eight-channel pods and simplifies the process of connecting to the DUT. The P6316 can connect directly to 8x2 square pin headers spaced on tenth-of-an-inch centres. When more attachment flexibility is required, the included ...
High quality passive voltage probes suitable for use ...
Description:
High quality passive voltage probes suitable for use with Tektronix oscilloscopes or as general purpose replacements. Each probe features compensation trimmers to allow matching to instruments. Supplied complete with accessories. Rated voltage CAT II 300V rms, CAT I 400V rms. ...
Low-cost general-purpose probes featuring a high input resistance ...
Description:
Low-cost general-purpose probes featuring a high input resistance for low probe loading. They can be adjusted for low-frequency and high-frequency compensation. • Bandwidth is DC to 500MHz (–3dB)• Attenuation ratio is 10:1• Cable length is 1.3M• Input impedance is 10Mohm ...
Tektronix high voltage probing solutions offer safety and ...
Description:
Tektronix high voltage probing solutions offer safety and accuracy in applications which include: floating measurements; switching power supply design; motor drive design; electronic ballast design; CRT display design; power converter design and service; power device evaluation. Overrange indicator. Safety ...